Komatsu PC500LC-10R Shop Manual Download | Manualshive

Page: 515 / 758

background image

1.

Adjust the stay (1).
Mounting position (2): 360 mm {14.2 in}
Mounting angle (3): 93 °

2.

Adjust the mirror (4).
Tightening torque of mounting bolt (5):6.0 to 7.0 Nm {0.61 to 0.71 kgm,4.41 to 5.14 lbft}
Mounting position (6): 85 mm {3.3 in}
Mounting angle (7): 27 °
Mounting angle (8): 9 °
Install the mirror so that its KOMATSU logo is at the right side of the machine body.

NOTICE

• Tighten the right and left bolts of each bracket al-

ternately so that their right and left clearances (R)
and (L) become equal.

• If the mirror and stay mounting bolts are tightened

excessively, the bracket will be damaged. Tighten
the bolts to the specified torque.

Adjust the mirror so that the side of the machine is reflected in
it as shown in the figure.

30 TESTING AND ADJUSTING

METHOD FOR ADJUSTING MIRRORS

PC500LC-10R

30-109

«
...
513
514
515
516
517
...
»

Summary of Contents for PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PC500LC-10R

Brand: New Holland Pages: 41

Brand: JACK RABBIT Pages: 32

460 Hydro-Scopic

Brand: Badger Equipment Company Pages: 4

Brand: Hyundai Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands