manualshive.com logo in svg

Komatsu PC500LC-10R, Shop Manual, Page: 408 / 758

Share
Download
Komatsu PC500LC-10R Shop Manual Download Page 408

CONTENTS

ABBREVIATION LIST .................................................................................................................................... 30-5
RELATED INFORMATION ON TESTING AND ADJUSTING ........................................................................30-11

TOOLS FOR TESTING AND ADJUSTING.............................................................................................30-11
SKETCH OF TOOLS FOR TESTING AND ADJUSTING ...................................................................... 30-16

ENGINE AND COOLING SYSTEM.............................................................................................................. 30-18

TEST ENGINE SPEED ......................................................................................................................... 30-18

METHOD FOR TESTING ENGINE SPEED ................................................................................... 30-18

TEST BOOST PRESSURE................................................................................................................... 30-21

METHOD FOR TESTING BOOST PRESSURE ON MACHINE MONITOR.................................... 30-21
METHOD FOR TESTING BOOST PRESSURE............................................................................. 30-22

TEST EXHAUST GAS TEMPERATURE ............................................................................................... 30-24

METHOD FOR TESTING EXHAUST GAS TEMPERATURE ......................................................... 30-24

TEST EXHAUST GAS COLOR............................................................................................................. 30-26

METHOD FOR TESTING EXHAUST GAS COLOR BY HANDY SMOKE CHECKER .................... 30-26
METHOD FOR TESTING EXHAUST GAS COLOR BY SMOKE METER ...................................... 30-27

TEST AND ADJUST VALVE CLEARANCE ........................................................................................... 30-28

METHOD FOR TESTING VALVE CLEARANCE ............................................................................ 30-28
METHOD FOR ADJUSTING VALVE CLEARANCE ....................................................................... 30-30

TEST COMPRESSION PRESSURE..................................................................................................... 30-31

METHOD FOR TESTING COMPRESSION PRESSURE............................................................... 30-31

TEST BLOWBY PRESSURE ................................................................................................................ 30-34

METHOD FOR TESTING BLOWBY PRESSURE ON MACHINE MONITOR ................................. 30-34
METHOD FOR TESTING BLOWBY PRESSURE BY TESTING TOOL.......................................... 30-35

TEST ENGINE OIL PRESSURE ........................................................................................................... 30-37

METHOD FOR TESTING ENGINE OIL PRESSURE BY MACHINE MONITOR ............................ 30-37
METHOD FOR TESTING ENGINE OIL PRESSURE BY TESTING TOOL .................................... 30-37

TEST FUEL PRESSURE ...................................................................................................................... 30-39

METHOD FOR TESTING FUEL PRESSURE ................................................................................ 30-39

TEST FUEL RETURN RATE AND LEAKAGE....................................................................................... 30-41

METHOD FOR TESTING FUEL RETURN RATE AND LEAKAGE................................................. 30-41

BLEED AIR FROM FUEL SYSTEM ...................................................................................................... 30-44

METHOD FOR BLEEDING AIR FROM FUEL SYSTEM ................................................................ 30-44

TEST FUEL CIRCUIT FOR LEAKAGE ................................................................................................. 30-47

METHOD FOR TESTING FUEL CIRCUIT FOR LEAKAGE ........................................................... 30-47

HANDLE CYLINDER CUT-OUT MODE OPERATION........................................................................... 30-49
HANDLE NO-INJECTION CRANKING OPERATION ............................................................................ 30-50
TEST FAN BELT ................................................................................................................................... 30-51

METHOD FOR TESTING OF FAN BELT ....................................................................................... 30-51

TEST ALTERNATOR BELT................................................................................................................... 30-52

METHOD FOR TESTING ALTERNATOR BELT............................................................................. 30-52

TEST AUTOMATIC TENSIONER ......................................................................................................... 30-54

METHOD FOR TESTING AUTOMATIC TENSIONER.................................................................... 30-54

TEST COOLING FAN SPEED  ............................................................................................................. 30-56

METHOD FOR TESTING COOLING FAN SPEED ........................................................................ 30-56

POWER TRAIN............................................................................................................................................ 30-57

TEST SWING CIRCLE BEARING CLEARANCE .................................................................................. 30-57

METHOD FOR TESTING SWING CIRCLE BEARING CLEARANCE ............................................ 30-57

UNDERCARRIAGE AND FRAME................................................................................................................ 30-58

TEST AND ADJUST TRACK TENSION................................................................................................ 30-58

METHOD FOR TESTING TRACK TENSION ................................................................................. 30-58
METHOD FOR ADJUSTING TRACK TENSION ............................................................................ 30-58

HYDRAULIC SYSTEM................................................................................................................................. 30-60

RELEASE REMAINING PRESSURE FROM HYDRAULIC SYSTEM.................................................... 30-60

METHOD FOR RELEASING REMAINING PRESSURE FROM HYDRAULIC TANK ..................... 30-60
METHOD FOR RELEASING REMAINING PRESSURE IN HYDRAULIC CYLINDER CIRCUIT .... 30-60
METHOD FOR RELEASING REMAINING PRESSURE FROM SWING MOTOR CIRCUIT........... 30-62

CONTENTS

30 TESTING AND ADJUSTING

30-2

PC500LC-10R

Summary of Contents for PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments