manualshive.com logo in svg

Komatsu PC500LC-10R, Shop Manual, Page: 595 / 758

Share
Download
Komatsu PC500LC-10R Shop Manual Download Page 595

Work equipment speed

Machine model

PC500LC-10R

Goo

d

No

goo

d

Engine

SAA6D125E-5

Item

Testing conditions

Unit

Standard val-

ue for new

machine

Repair limit

Meas-

ured val-

ue

Boom

RAISE

•

Hydraulic oil temperature: 45 to
55 °C

•

Fuel control dial: MAX (High
idle) position

•

Working mode: P (Power
Mode)

•

Measurement range: Between
bucket ground point and
RAISE stroke end

•

Measurement posture: Fully
extended boom
See the STANDARD VALUE
TABLE, “MACHINE POSTURE
AND PROCEDURE FOR
MEASURING PERFORM-
ANCE”, “Work equipment 2”.

 sec

3.8 to 4.6

5.0 or less

Arm IN

•

Hydraulic oil temperature: 45 to
55 °C

•

Fuel control dial: MAX (High
idle) position

•

Working mode: P (Power
Mode)

•

Measurement range: Between
arm OUT stroke end and arm
IN stroke end

•

Measurement posture: Boom
top face horizontal
See the STANDARD VALUE
TABLE, “MACHINE POSTURE
AND PROCEDURE FOR
MEASURING PERFORM-
ANCE”, “Work equipment 3”.

 sec

4.1 to 5.1

5.4 or less

30 TESTING AND ADJUSTING

Pm CLINIC SERVICE

PC500LC-10R

30-189

Summary of Contents for PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments