KNECHT HV 203 Operating Instructions Manual Download Page 66

Page: 66 / 70

10. Care and maintenance

For all work on the grinding machine, observe the locally applicable
safety and accident prevention regulations as well as instructions in the
“Safety” and “Important notes” section of the operating instructions.

CAUTION

10.1 Cleaning

The grinding units must be cleaned after each sharpening, otherwise the grinding sludge will dry
and will be difficult to remove.

After cleaning the grinding units, we recommend the products listed in the lubricant table for care
(chapter 10.1.1).

10.1.1 Lubricant table

Lubrication work

Interflon

Würth

SHELL

EXXON Mobil

Cleaning and care of machine
parts

Dry clean
stainless steel

Stainless steel
care spray

Risella 917

Marcol 82

Lubricate threads and sliding
surfaces

Fin Grease

Multi-purpose
grease

Gadus S2

Ronex MP

10.2 Maintenance plan (one-shift operation)

Interval

Assembly

Maintenance task

Daily

All surfaces

Clean with soft cloth and care spray.

Weekly

Star handle threads

Lubricate with multi-purpose grease.

Guideways

Clean and lubricate with multi-purpose grease.

Annually

Contact the service department of KNECHT
Maschinenbau GmbH.

Summary of Contents for HV 203







































































Search results

Summary of Contents for HV 203

Reviews:

Related manuals for HV 203

Brands by name

Popular brands

KNECHT HV 203, Operating Instructions Manual

Search results

Summary of Contents for HV 203

Reviews:

Related manuals for HV 203

Brands by name

Popular brands