KNECHT HV 203 Operating Instructions Manual Download Page 28 | Manualshive

Page: 28 / 70

background image

29

7.1.3 Positioning the knife on the grinding wheel

The cutting edge of the knife (7-12/1) must lie
approximately on the center of the grinding
wheel.

To do so, loosen the lower clamping lever (7-13/1)
by rotating counterclockwise and move the entire
grinding unit until the cutting edge of the knife is
approx. on the center of the grinding wheel (see
Figure 7-12).

Retighten the lower clamping lever (7-13/1).

7. Operating the HV 203

Figure 7-12

Knife position on the grinding

wheel

Figure 7-13

Adjusting the knife to the center

of the grinding wheel

1

1

«
...
26
27
28
29
30
...
»

Summary of Contents for HV 203







































































Reviews:

No comments

Related manuals for HV 203

Brand: Femi Pages: 36

Brand: Fein Pages: 200

Brand: BRODBECK IRONWORKS Pages: 23

Brand: Urrea Pages: 8

Brand: Sheffield Pages: 8

Brand: YATO Pages: 126

Brand: BRAYER Pages: 44

Brand: SHARKS Pages: 73

Brand: Scheppach Pages: 48

Brand: Kobalt Pages: 33

Brand: Scheppach Pages: 44

Brand: Scheppach Pages: 104

Brand: Fimar Pages: 96

Brand: ARO Pages: 11

Brand: Sunex HD Pages: 11

Brand: PRETUL Pages: 24

Brand: Art's-Way Manufacturing Pages: 64

Brand: Jet Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands