KNECHT HV 203 Operating Instructions Manual Download Page 29 | Manualshive

Page: 29 / 70

background image

30

Figure 7-14

Loosening the clamping lever

Figure 7-15

Aligning the knife on the grinding

wheel

Figure 7-16

Tightening the clamping lever

7.1.4 Aligning the knife on the grinding wheel

Slightly loosen the clamping lever (7-14/1) until
the grinding plate with the clamped knife can be
moved.

NOTE

The best grinding results are achieved by
engaging the full width of the grinding
wheel on the cutting edge of the knife.

Swivel the grinding plate with the clamped
knife until the full width of the grinding wheel is
engaged.

Tighten clamping lever (7-16/1).

7. Operating the HV 203

1

1

«
...
27
28
29
30
31
...
»

Summary of Contents for HV 203







































































Reviews:

No comments

Related manuals for HV 203

Brand: Hendi Pages: 36

Brand: La Pavoni Pages: 108

Brand: Twothousand Pages: 3

PKR CGA Coffee Grinder Mill Kit

Brand: PROKRAFT Pages: 5

Brand: Baratza Pages: 23

Brand: Power Glide Pages: 4

Brand: Colombini Pages: 11

Brand: Zoeller Pages: 12

Brand: Panasonic Pages: 172

Brand: BeON Pages: 16

Brand: Hitachi Koki Pages: 40

Brand: Hitachi Koki Pages: 45

Brand: Hitachi Koki Pages: 52

Brand: Chicago Electric Pages: 16

Brand: Duronic Pages: 59

Brand: Flex Pages: 60

Bulut BULUPOL-3

Brand: BMS Pages: 9

KH 3039 ANGLE GRINDER

Brand: Parkside Pages: 89

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands