KNECHT HV 203 Operating Instructions Manual Download Page 60

Page: 60 / 70

Figure 9-35

Swiveling the grinding plate back-

ward into the anti-rotation device

Figure 9-36

Clamping the knife onto the

grinding plate

9.2.7 Clamping cutter knives

Serious cuts may occur when handling cutter knives. Only transport
cutter knives using transport devices intended for this purpose.

Protective gloves and safety shoes must be worn.

CAUTION

ATTENTION

Before clamping the knife, check whether the
grinding plate fits the knife to be ground.
Compare the inscription of the grinding plate
with that of the knife.

The use of an unsuitable grinding plate can
damage the knife and grinding plate.

Swivel the grinding plate (9-35/1) back as far as it
will go. It is now secured against rotating.

Position the grinding plate in such a way that the
mounting area of the knife is easily accessible.

Clamp the knife (9-36/1) onto the grinding plate
(9-36/2).

9. Operating the HV 262

Summary of Contents for HV 203







































































Search results

Summary of Contents for HV 203

Reviews:

Related manuals for HV 203

Brands by name

Popular brands

KNECHT HV 203, Operating Instructions Manual

Search results

Summary of Contents for HV 203

Reviews:

Related manuals for HV 203

Brands by name

Popular brands