KNECHT HV 203 Operating Instructions Manual Download Page 42 | Manualshive

Page: 42 / 70

background image

43

7.2.4 Setting the grinding angle

To adjust the grinding angle, place the knife on
the grinding wheel.

Loosen the upper clamping lever (7-44/1) by
turning it counterclockwise.

Turn the hand wheel (7-45/1) until the pointer
(7-45/2) shows the desired angle on the angle
scale (7-44/3).

Retighten the upper clamping lever (7-44/1).

Figure 7-44

Loosening the clamping lever

7. Operating the HV 203

1

Figure 7-45

Setting the grinding angle

3

1

2

«
...
40
41
42
43
44
...
»

Summary of Contents for HV 203







































































Reviews:

No comments

Related manuals for HV 203

Brand: Parkside Pages: 174

POLY-PTX 802 HT

Brand: eisenblatter Pages: 20

Brand: Bunn Pages: 2

Brand: Cuisinart Pages: 20

Brand: Northern Industrial Pages: 12

050-M80-013-T48

Brand: QUAMAR Pages: 100

Brand: Kitchener Pages: 8

Brand: Batavia Pages: 34

Brand: Minimal Pages: 2

Brand: Hilti Pages: 24

Brand: Eastwood Pages: 8

Brand: MUHLER Pages: 16

Brand: Parkside Pages: 228

Brand: EINHELL ERGO TOOLS Pages: 34

Brand: Worx Pages: 12

Brand: Worx Pages: 92

Brand: Jet Pages: 12

Brand: SUHNER Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands