Kirisun DP580-01 Page 62 User Manual Download

Page: 62 / 69

DP580-01 Digital Two-way Radio

b) Select “Scan”.
c) Select “Scan List”, and then select a target channel.
d) Select “Set as prior channel 1” to set the channel as prior channel 1.
Repeat these steps while adding a prior channel 2.

5) Enabling/Disabling Scan

a) In the home page, press

to enter the menu.

b) Selec

t “Scan”.

c) Enable or disable scan.

Note:

During the scan, the radio receives data (including short messages, GPS data, telemetry data or PC data)

and digital signaling only through the selected channel (starting channel of scan).

6) Responding during Scan

During scan, if detects a channel with traffic, the radio will stay on this channel for a set period, which is

called dwelling time (programmed by dealer through programming software).

Summary of Contents for DP580-01






































































Search results

Summary of Contents for DP580-01

Reviews:

Related manuals for DP580-01

Brands by name

Popular brands

Kirisun DP580-01, User Manual

Search results

Summary of Contents for DP580-01

Reviews:

Related manuals for DP580-01

Brands by name

Popular brands