Kirisun DP580-01 Page 27 User Manual Download | Manualshive

Page: 27 / 69

background image

User Manual

26

three months.



When the battery is fully charged or the battery power is above the level of low power alert, do not
charge the battery, or it may affect the battery life and performance. Please take out the battery from
the charger after it is fully charged.



When the radio enters the state of low voltage alarm, please charge the battery before using it and do
not force to power on the radio in case that the battery life
and performance is impaired.



There is protection circuit inside KB-75lithium battery. The
power supply will be cut off in state of low power, and when
you charge it in the charger, the indicator will glow after 1-5
minutes.

3

Attaching the Accessories

3.1 Attaching/Detaching the Battery

◆

Attaching the Battery

«
...
25
26
27
28
29
...
»

Summary of Contents for DP580-01






































































Reviews:

No comments

Related manuals for DP580-01

Brand: JBL Pages: 25

Brand: Simons Voss Technologies Pages: 116

Brand: Uniden Pages: 16

Brand: Retekess Pages: 2

Brand: Covalue Pages: 24

microTALK CXT125

Brand: Cobra Pages: 1

Brand: Cobra Pages: 22

Brand: Motorola Pages: 756

DAB Table Radio

Brand: Tangent Pages: 15

Brand: Tangent Pages: 196

FT-100 Micro Mobile

Brand: Yaesu Pages: 123

Brand: Icom Pages: 2

Brand: Grace Pages: 44

Brand: Garmin Pages: 56

Brand: Orion Pages: 11

Brand: OXX Digital Pages: 12

PRODIGI RDR2750

Brand: RCA Pages: 13

Brand: Danita Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands