Kirisun DP580-01 User Manual Download Page 33 | Manualshive

Page: 33 / 69

background image

User Manual

32

Note:

Short Press: press and release quickly.

Long Press: press and hold for a while (press duration can be set by programming software)

No

Programmable
Feature

Application

1

No Function

Press the key, and the radio will not respond.

2

High/Low Power

Switch to high/low power.

3

Listen

If the CTCSS is enabled for the current analogue channel, press the

key to switch to carrier squelch mode (i.e. cancel the CTCSS).

Voice is output when the carrier is matched. Press the key again to

go back to the previous state.

4

Emergency Alarm

Send an emergency alarm. It is used to seek help under

emergency.

5

Exit Emergency

Alarm

Quit the state of emergency alarm.

6

Squelch On/Off

Enable/disable squelch. It can be used to receive week signals in

«
...
31
32
33
34
35
...
»

Summary of Contents for DP580-01






































































Reviews:

No comments

Related manuals for DP580-01

Heritage Bluetooth

Brand: HAEGER Pages: 40

Brand: Radio Shack Pages: 48

Brand: Sungale Pages: 24

Brand: QFX Pages: 6

Brand: Campbell Pages: 51

Brand: Clatronic Pages: 14

Brand: RoadCom Pages: 11

Brand: SFE Pages: 15

Brand: Holtek Pages: 44

Lowrance LVR-880EU

Brand: Navico Pages: 60

Brand: LENCO Pages: 91

Brand: Bosch Pages: 7

Brand: Motorola Pages: 10

Brand: Motorola Pages: 9

Brand: Motorola Pages: 18

KEM-PK34301-03 Talkabout

Brand: Motorola Pages: 4

KEM-ML14190-33A

Brand: Motorola Pages: 2

Brand: Motorola Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands