Kirisun DP580-01 Page 18 User Manual Download

Page: 18 / 69

DP580-01 Digital Two-way Radio

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the

following measures:

—

Reorient or relocate the receiving antenna.

—

Increase the separation between the equipment and receiver.

—

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—

Consult the dealer or an experienced radio/TV technician for help

Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.

Summary of Contents for DP580-01






































































Search results

Summary of Contents for DP580-01

Reviews:

Related manuals for DP580-01

Brands by name

Popular brands

Kirisun DP580-01, User Manual

Search results

Summary of Contents for DP580-01

Reviews:

Related manuals for DP580-01

Brands by name

Popular brands