Kirisun DP580-01 User Manual Download | Manualshive

Page: 57 / 69

background image

User Manual

56

screen without the ability to receive all the other information except the un-stun signaling. All the operation

on the radio is valid except powering on/off.

The activated radio will go back to normal from being stunned.

2) Sending Stun/Un-Stun Signaling

a) In the home page, press

to enter the menu.

b) Select “Contact”.
c) Select “Contact List” and a target private call contact.
d) Select “Stun/Un-Stun”.

e) The screen shows the alias or ID of the target radio and the radio indicates that it is sending

stun/un-stun signaling. The red indicator glows.

f) Wait for response from the target radio.
g) If the radio receives a response from the target radio, the message “Stun succeeded”/“Un-stun

suc

ceeded” will be displayed; otherwise “Request timed out” will be displayed.

Note:

If the retry count is used up and no response is received, the radio will automatically stop sending signaling
with a prompt of “Request timed out”.

«
...
55
56
57
58
59
...
»

Summary of Contents for DP580-01






































































Reviews:

No comments

Related manuals for DP580-01

Brand: Akai Pages: 16

Brand: Yaesu Pages: 51

Brand: E.F. Johnson Pages: 69

Brand: Radwin Pages: 62

Brand: Retevis Pages: 9

Brand: ToooAir Pages: 2

Brand: Midland Pages: 4

Brand: Radio Shack Pages: 24

Brand: NAVICOM Pages: 27

Brand: NAVICOM Pages: 30

Brand: Navico Pages: 54

Brand: AvaLAN Pages: 9

Brand: Albrecht Pages: 72

Brand: Medion Pages: 294

Brand: S Audio Pages: 52

Brand: King Champion Pages: 16

Brand: CTC Union Pages: 22

Brand: Team Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands