Kirisun DP580-01 User Manual Download Page 34 | Manualshive

Page: 34 / 69

background image

DP580-01 Digital Two-way Radio

33

No

Programmable
Feature

Application

an analogue channel.

7

Broadcast Call

Set the function of broadcast call.

8

Scan

Enable/disable scanning. It is used to listen to the communication

activities on other channels.

9

Prompt Tone On/Off

Enable/disable all prompt tones.

11

Zone Selection

Switch among different zones. Zones are programmed using CPS

programming software.

12

Repeater/Talk

Around

Enable/disable repeater function for the channel.

13

Delete Noise

Channel

If you don’t need a channel found through scanning, press the key

to delete the channel from the scan list.

«
...
32
33
34
35
36
...
»

Summary of Contents for DP580-01






































































Reviews:

No comments

Related manuals for DP580-01

Brand: Uniden Pages: 32

Brand: tez audio Pages: 4

Brand: Sparc Pages: 2

Brand: Clatronic Pages: 14

Brand: Telefunken Pages: 16

Talkabout T5MP3

Brand: Motorola Pages: 36

Talkabout T5800

Brand: Motorola Pages: 42

Talkabout T5622

Brand: Motorola Pages: 2

NetWorks Speaker

Brand: Tivoli Audio Pages: 24

Model One Digital

Brand: Tivoli Audio Pages: 429

Brand: Quanzhou Pages: 45

Brand: Heathkit Pages: 41

Brand: Icom Pages: 1

Brand: Garmin Pages: 132

Brand: Team Pages: 25

Brand: Fisher-Price Pages: 8

Brand: K-PO Pages: 12

Brand: Ham International Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands