Kirisun DP580-01 Page 28 User Manual Download

Page: 28 / 69

DP580-01 Digital Two-way Radio

(1) Slightly press the top of the belt clip as shown in

①

;

(2) Align the battery with the battery installation base at the back and insert the battery as shown in

②

(3) Slide the battery along the direction as shown in

③

until the battery is fit into the right position.

(4) Slightly press the battery top as shown in

④

until the battery is locked by the latch.

◆

Detaching the battery

(1) For detaching the battery, please first turn off the radio.
(2) Slide the battery latch along the direction as shown in

①

to bounce the

battery as shown in

②

(3) Slide to take out the battery along the direction as shown in

③

. If there

is belt clip, slightly press the belt clip top as shown in

④

and slide the

battery along the direction as shown in

③

to take out the battery.

Note:



Do not throw the battery terminals with short circuit or battery into fire.



Do not remove the battery case without permission.

Summary of Contents for DP580-01






































































Search results

Summary of Contents for DP580-01

Reviews:

Related manuals for DP580-01

Brands by name

Popular brands

Kirisun DP580-01, User Manual

Search results

Summary of Contents for DP580-01

Reviews:

Related manuals for DP580-01

Brands by name

Popular brands