Kirisun DP580-01 User Manual Download Page 58

Page: 58 / 69

DP580-01 Digital Two-way Radio

11.4

Radio Kill

This function allows the user to kill the target radio through air signaling. After the target radio is killed, the

key configuration data will be cleared and the radio is powered off automatically. You cannot operate the

radio after powering it on.

The killed radio can only be revived by the authorized dealer or supplier.

This feature is used to prevent the lost radio from being used and the key configuration data from being

stolen.

Note:



Once the radio is killed, the configuration data will be lost and the radio cannot go back to

normal after reboot, so please operate with due care!



The killed radio can only be revived by authorized dealer or supplier.

1) Receiving Kill Signaling

After a target radio receives the kill signaling and is killed successfully, it responds with a message of

successful operation to the caller radio; otherwise response fails.

After a radio is killed, its configuration data is cleared and it is powered off automatically.

Summary of Contents for DP580-01






































































Search results

Summary of Contents for DP580-01

Reviews:

Related manuals for DP580-01

Brands by name

Popular brands

Kirisun DP580-01, User Manual

Search results

Summary of Contents for DP580-01

Reviews:

Related manuals for DP580-01

Brands by name

Popular brands