Keysight 53210A User Manual Download Page 45

Page: 45 / 247

Preparation for Use

Keysight 53210A User’s Guide

The emulation mode can also be enabled using the command:

SYSTem:LANGuage "<language>"

SYSTem:LANGuage?

(query form)

language

selects the SCPI command set used. Specifying

53181A

enables the

emulation mode. Specifying either

53210A

disables the mode.

With 53100-series compatibility mode selected, all programming is through the

counter's remote interface (LAN, USB, GPIB). The counter display responds

according to the remote commands received.
Pressing any front panel key while in 53100 compatibility mode returns the

counter to 53200 series mode as prompted. Setting or changing to either mode

requires the instrument to be restarted.

When updating the instrument firmware

“53210A mode” must be set

Documentation of the

53181A

command set

is not

provided with this (53210A)

instrument. Usage of this older SCPI command set is discouraged for new use,

but is available for customers who require it.

Securing the Instrument

The 53210A counter can be secured to the National Industrial Security Program

Operating Manual (NISPOM) standard as shown below.

Summary of Contents for 53210A
























































































































































































































































Search results

Summary of Contents for 53210A

Reviews:

Related manuals for 53210A

Brands by name

Popular brands

Keysight 53210A, User Manual

Search results

Summary of Contents for 53210A

Reviews:

Related manuals for 53210A

Brands by name

Popular brands