manualshive.com logo in svg

Keysight 53210A, User Manual

Share
Download
Keysight 53210A User Manual Download Page 60

2

53210A Software Installation and Interface Configuration

60

Keysight 53210A User’s Guide

Figure 2-3

Starting Keysight Connection Expert.

Locating the Instruments

Keysight Connection Expert opens with a welcome screen and window similar to 

that shown in 

Figure 2-4

. The computer interfaces configured during installation 

are displayed in the left column (

Explorer

 pane), the properties of the configured 

interface are displayed in the right column (

Properties

 pane).

To search the network for the counter, click 

and select 

LAN Instrument

 

located on the Connection Expert tool bar. After selecting 

LAN Instrument

, 

Connection Expert performs an automatic find (Auto Find) of all instruments on 

the same subnet as the computer.
Select the counter from the list and then click ‘OK’. Communication paths to the 

instruments are verified and the instruments are added to the configured 

interface. Instruments added to the LAN in this manner are subsequently 

programmed using 

VXI-11 protocol

.

Clicking the icon opens 
the pop-up menu

Summary of Contents for 53210A
























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands