Keysight 53210A User Manual Download Page 27

Page: 27 / 247

Preparation for Use

Keysight 53210A User’s Guide

Display

The layout of the 53210A display is shown in

Figure 1-2

Figure 1-2

The 53210A Display.

Channel Configuration

Main Measurement Display

Softkey Navigation

Input Settings

: measurement start edge

10% : trigger threshold
AC

: input coupling (ac or dc)

1MW : input Impedance (1MW, 50W)
5V

: input Range (5V, 50V, 500V)

Probe : probe enabled
BW : bandwidth filter enabled

Channel and Function

Soft Keys

Secondary Measurements

Main Measurement

Data Entry Area

Status Indicators

RMT: remote (LAN, USB, GPIB) operation

ExtRef: external frequency reference

ExtRef : invalid external reference

ExtTrig: external trigger source
Battery charge status

Ch. 1

Gate

Battery status:
   charge level
   black – user disabled
   red – software disabled

Summary of Contents for 53210A
























































































































































































































































Search results

Summary of Contents for 53210A

Reviews:

Keysight 53210A, User Manual, Page: 27 / 247

Search results

Summary of Contents for 53210A

Reviews: