manualshive.com logo in svg

Keysight 53210A, User Manual

Share
Download
Keysight 53210A User Manual Download Page 4

4

Keysight 53210A User’s Guide

Exclusive Remedies

THE REMEDIES PROVIDED HEREIN ARE THE CUSTOMER'S SOLE AND 

EXCLUSIVE REMEDIES. KEYSIGHT TECHNOLOGIES SHALL NOT BE LIABLE FOR 

ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, 

WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY.

Restricted Rights Legend

U.S. Government Restricted Rights. Software and technical data rights granted to 

the federal government include only those rights customarily provided to end user 

customers. Keysight provides this customary commercial license in Software and 

technical data pursuant to FAR 12.211 (Technical Data) and 12.212 (Computer 

Software) and, for the Department of Defense, DFARS 252.227-7015 (Technical 

Data - Commercial Items) and DFARS 227.7202-3 (Rights in Commercial 

Computer Software or Computer Software Documentation).

Trademarks

Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. 

Summary of Contents for 53210A
























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands