Keysight 53210A User Manual Download Page 40

Page: 40 / 247

Preparation for Use

Keysight 53210A User’s Guide

Note that pressing any key with the display turned off, turns the display back on.

Screen Capture

For documentation of product testing or as a convenience in gathering data, the

contents of the counter display can be captured and saved.
The keys related to this feature are shown below.

The content captured is the display state at the time the

[Utility]

key is pressed.

The file format is selectable as either

bmp

(bitmap file format) or png (portable

network graphics (bitmap) format). Files may be store in internal flash memory or

to an external USB device.
See

Chapter 7

for information on selecting paths and creating file names.

User Interaction

The features described in this section are related to the user’s physical interaction

with the instrument.

Summary of Contents for 53210A
























































































































































































































































Search results

Summary of Contents for 53210A

Reviews:

Related manuals for 53210A

Brands by name

Popular brands

Keysight 53210A, User Manual

Search results

Summary of Contents for 53210A

Reviews:

Related manuals for 53210A

Brands by name

Popular brands