background image

5. Tighten up the clamping bolts 

5

 with the self-locking nuts 

6

.

It must be just possible to manually move the screw connections.

10.6  Cleaning the cooler

The frequency of cleaning is mainly dependent on local operating conditions.
Severe clogging of the coolers causes overheating and machine damage.
Check coolers regularly for clogging.
Avoid creating dust eddies. Wear breathing protection if necessary.
Do not clean the coolers/radiators with a sharp instrument as they may be damaged.
A severely contaminated cooler/radiator should be cleaned by KAESER SERVICE.

Material Compressed air

Breathing mask (if necessary)
Water or steam jet blaster

Precondition The machine is placed over a washing station equipped with an oil separator.

The machine is switched off.
The machine has cooled down.
The machine is fully vented, the pressure gauge reads 0 psig.
All compressed air consumers are disconnected and the air outlet valves are open.
The «battery isolating switch» is turned off.

Damage to the machine can be caused by water or steam jets.

Direct water or steam jets can damage or destroy electrical components and indicating in‐

struments.
➤ Cover up electrical components such as the control cabinet, alternator, starter and in‐

struments.

➤ Do not direct water or steam jets at sensitive components such as alternator, starter or

indicating instruments.

➤ Deploy the extension pole of the pressure washer at a distance of at least 1.7 ft. and an

approximately 90° angle to the cooler/radiator surface.

➤ Open both doors.

10.6.1  Cleaning the compressor cooler and engine radiator

The compressor oil cooler and engine coolant radiator are combined in a single cooler block.

10 Maintenance

10.6 Cleaning the cooler

142

Operator Manual    Screw Compressor  
M114  SIGMA CONTROL SMART

No.: 901765 05 USE

Summary of Contents for SIGMA CONTROL SMART M114













































































































































































































































































































































































Reviews: