Juniper PTX5000 Hardware Manual Download Page 521 | Manualshive

Page: 521 / 721

background image

2. Carefully align the bottom and then the top edges of the Control Board with the guides inside the

chassis.

3. Slide the Control Board into the chassis, carefully ensuring that it is correctly aligned.

4. Twist both ejector handles clockwise to seat the host subsystem until the ejectors latch into the

faceplate.

NOTE: While installing, ensure that you install the Control Board that is compatible with the
Routing Engine. Install the Routing Engine RE-DUO-C2600-16G into the Control Board CB-
PTX and Routing Engine RE-PTX-X8-64G into the Control Board CB2-PTX only.

Figure 271: Installing the CB2-PTX Control Board

5. To verify that the Control Board is installed correctly and functioning normally:

• Connect an Ethernet cable to the HOST/ETHERNET port on the Control Board. If the host

subsystem is operational, the ACT port LED is lit to indicate Ethernet activity. If you can run the
CLI from a management device attached to the Control Board, the Control Board is installed
correctly.

• Verify that the green OK LED on the Control Board faceplate is lit steadily green. The green OK

LED should light steadily a few minutes after the Control Board is installed.

• Verify that the FAIL LED on the Control Board faceplate is not lit. If the FAIL LED is lit steadily,

remove and install the Control Board again. If the FAIL LED still lights steadily, the Control Board
is not functioning properly. Contact your customer support representative.

503

«
...
519
520
521
522
523
...
»

Summary of Contents for PTX5000


















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PTX5000

Brand: ZETR Pages: 2

Brand: CallDirect Pages: 33

Brand: TDC Pages: 27

Brand: Cambium Networks Pages: 29

Brand: Pakedge Device & Software Pages: 20

Brand: Ubiquiti Pages: 40

Brand: Yamaha Pages: 24

Brand: Yamaha Pages: 5

Brand: Juniper Pages: 502

Brand: Patton electronics Pages: 12

Brand: Lanner Pages: 63

Brand: TP-Link Pages: 110

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

Brand: Gbord Pages: 8

Brand: VCS Pages: 118

Brand: Observint Pages: 117

Brand: PaloAlto Networks Pages: 28

Brand: Tenda Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands