manualshive.com logo in svg

Juniper PTX5000, Hardware Manual

The Juniper PTX5000 is a high-performance networking device designed for large-scale data centers and service providers. To learn more about its features and specifications, you can download the free Hardware Manual from manualshive.com. This manual provides detailed instructions on how to operate and maintain your PTX5000.

Share
Download
background image

6. Attach the other end of the cable to the console or auxiliary device.

Figure 136: Connecting to the Console or Auxiliary Port on the Control Board

 1

—

Console port

 2

—

Auxiliary port

SEE ALSO

PTX5000 Control Board Description  |  131

PTX5000 Management Interface Cable Specifications  |  193

RJ-45 Connector Pinouts for the PTX5000 Auxiliary and Console Ports  |  194

Connecting the PTX5000 to a Management Ethernet Device

To connect the Routing Engines in a PTX5000 to a network for management of the PTX5000, connect a
UTP Category 5 Ethernet cable with an RJ-45 connector to the HOST/ETHERNET port on a Control
Board.

NOTE: For PTX5000 routers with two host subsystems, we recommend that you connect both
Control Boards to a network. One cable is provided in the accessory box. To connect another
cable to the HOST/ETHERNET port on the other Control Board, you must provide an additional
cable.

To connect a cable to a network device:

1. Attach an ESD grounding strap to your bare wrist, and connect the strap to one of the ESD points on

the chassis.

276

Summary of Contents for PTX5000


















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PTX5000

Parker H Series Installation & Service Instructions Manual preview
H Series
Brand: Parker Pages: 344
Patton electronics Patton SmartNode 2300 Series Specification Sheet preview
Patton SmartNode 2300 Series
Brand: Patton electronics Pages: 2
Paradyne 8540 Installation Instructions Manual preview
8540
Brand: Paradyne Pages: 12
Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Brand: Radwin Pages: 122
D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Brand: D-Link Pages: 31
Oracle Talari E1000 Installation Manual preview
Talari E1000
Brand: Oracle Pages: 24
FOR-A MFR-16DTIO Installation Manual preview
MFR-16DTIO
Brand: FOR-A Pages: 2
PaloAlto Networks ION 1200 Series Hardware Reference Manual preview
ION 1200 Series
Brand: PaloAlto Networks Pages: 90
American Megatrends StorTrends 1312-P Specifications preview
StorTrends 1312-P
Brand: American Megatrends Pages: 2
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Brand: Enterasys Pages: 58
ADIC FCR 200 Operator'S Manual preview
FCR 200
Brand: ADIC Pages: 140
INNOSILICON T3-43T User Manual preview
T3-43T
Brand: INNOSILICON Pages: 11
Allied Telesis Routers and Switches Datasheet preview
Routers and Switches
Brand: Allied Telesis Pages: 15
Paradyne Hotwire 5620 RTU Installation Instructions Manual preview
Hotwire 5620 RTU
Brand: Paradyne Pages: 20
Allied Telesis AR440S Hardware Reference Manual preview
AR440S
Brand: Allied Telesis Pages: 44
Aztech DSL906 1DA Series Easy Start preview
DSL906 1DA Series
Brand: Aztech Pages: 15
Ozito RTB-001 Instruction Manual preview
RTB-001
Brand: Ozito Pages: 8
Billion BiPAC 7800NL User Manual preview
BiPAC 7800NL
Brand: Billion Pages: 170

Brands by name

Popular brands

Load more brands