J&J Amusements Bumper Boat 2014 Service Manual Download

Page: 95 / 168

3-7

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

HANDLEBAR ASSEMBLY

The handlebar assembly has two parts and is mounted

on the motor with four 3/8” hex-head-mount bolts.

(Part # 2-10-0003 handlebar mount plate )

(Part # 2-10-0002 handlebar )

Remove the gear box

(see page 3-33).

Remove the hex-head motor-mount bolts.

After the bolts are removed, slide the plate up the drive

shaft housing.

Note

The drive shaft housing will be loose from the motor.

The handlebar is now free from the motor and can be

removed.

visit www.jjamusements.com and download a copy of our
complete accessory catalog!

Summary of Contents for Bumper Boat 2014








































































































































































Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands

J&J Amusements Bumper Boat 2014, Service Manual

Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands