J&J Amusements Bumper Boat 2014 Service Manual Download | Manualshive

Page: 37 / 168

background image

1-3

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

NOTICE:

All power goes through breaker.

When breaker is in the off position, there will be no reading

displayed on volt meter, (The volt meter will display 0 volts)

and the batteries cannot be charged.

REMOVAL/INSTALLATION.

Disconnect the (-) negative cable from battery #1.

Disconnect the (+) positive cable leading to the breaker from

battery #4.

Disconnect the (+) positive cable leading to the breaker from

the power post.

Note:

Your J&J Blaster Boat may be equipped with one of two types of power

posts.

The Pre-2012 version utilizes two rounded-style posts;

one for the positive feed and one for the negative feed.

Blaster Boats built during the 2012 model year changed to a single,

rectangular-style post that contains both the negative and positive feeds.

BREAKER SWITCH (Electric only)

Battery 4

Battery 3

Battery 1

Battery 2

Disconnect negative

Disconnect positive

2 unit fiberglass CHARGER ENCLOSURES.
part # 2-80-A00062.

Power post, pre -2012

Power post, post-2012

«
...
35
36
37
38
39
...
»

Summary of Contents for Bumper Boat 2014









































































































































































Reviews:

No comments

Related manuals for Bumper Boat 2014

Brand: Parker Pages: 68

Brand: Nacra Pages: 28

Brand: Walker Bay Pages: 8

Brand: Newage Pages: 39

Brand: Maxxon Pages: 6

Brand: Marine Power Pages: 79

Explorer 14.6 DLX

Brand: Pelican Pages: 10

Brand: Polaris Pages: 90

WaveRunner EX 2021

Brand: Yamaha Pages: 110

210FSH SPORT 2020

Brand: Yamaha Pages: 146

Brand: Klarfit Pages: 56

Brand: Sea Eagle Boats Pages: 17

Brand: Sea Ray Pages: 50

Brand: Sea Ray Pages: 154

Brand: Sea-doo Pages: 557

Brand: Pyranha Pages: 8

Brand: MARKER ONE Pages: 110

West Wight Potter 19

Brand: International Marine Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands