J&J Amusements Bumper Boat 2014 Service Manual Download

Page: 108 / 168

3-20

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

Remove the motor cover and neoprene protector

(see page 3-3).

Remove the magnetic trigger by removing the 1/4” shoulder

bolt with an allen wrench.

Inspect the nylon bushing and shoulder bolt.

Replace as needed.

Align the rode with the slot in the handlebars.

Make sure the magnet in the trigger is pointed down, facing

the solid state switch.

Tighten the shoulder bolt.

NOTICE: Mounting the magnet upside down will result in a

poor or nonfunctional sold state switch.

Tighten the shoulder bolt.

MAGNETIC TRIGGER

Bottom

VISIT WWW.JJAMUSEMENTS.COM/TECHNICAL/INDEX.HTM FOR
TECHNICAL INFORMATION RELATED TO OUR PRODUCTS.

Summary of Contents for Bumper Boat 2014








































































































































































Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands

J&J Amusements Bumper Boat 2014, Service Manual

Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands