J&J Amusements Bumper Boat 2014 Service Manual Download

Page: 84 / 168

2-16

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

Fully inflate the tube.

Place three to four drops of washing detergent in a

spray bottle with water.

Check small areas of the tube at a time, spraying the

surface of the tube and looking for any bubbles.

Draw a small circle around any punctures or rips

in the tube (for easy location of the repair), then

deflate tube.

NOTICE:

The glue and patch will bubble up and fail to bond

properly if the tube is fully inflated when the repair

is made.

Do not attempt to patch around or near a tube

seam, as the patch will not bond.

CHECKING SUPER TUBE FOR LEAKS

SUPERTUBE PATCH KIT #003370

Summary of Contents for Bumper Boat 2014








































































































































































Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands

J&J Amusements Bumper Boat 2014, Service Manual

Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands