J&J Amusements Bumper Boat 2014 Service Manual Download

Page: 80 / 168

2-12

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

BATTERY-FILL KIT INSTALLATION (Electric only)

Remove the caps from the batteries and place aside for later

use.

Remove the manifold valves from the hose T-fittings.

Loosely install the manifold valves into the batteries.

Make sure the manifold valves are flush with the battery be-

fore tightening.

Push the hose T-fittings into the manifolds.

Use equal pressure until the fittings snap into place.

NOTICE Be careful not to damage the T-fitting o-ring.

TECH TIP: Wet the T-Fitting with distilled water to help it slip

more easily into the manifold.

NOTICE Twist the manifolds slightly to remove any kinks in

the water lines. All kinks must be removed for the watering

system to function correctly.

Install the filler tube from the boat hull to fill the system.

Push and slightly twist the hose to install.

Manifold Valve

Remove kinks

T-fitting

Summary of Contents for Bumper Boat 2014








































































































































































Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands

J&J Amusements Bumper Boat 2014, Service Manual

Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands