J&J Amusements Bumper Boat 2014 Service Manual Download | Manualshive

Page: 159 / 168

background image

6-3

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

BOAT TOP DECALS

J&J Amusements website decal is located at the right

rear of the boat top under the vent plate.

(J&J #009800)

“Blaster Boat” decal is located on the

boat top above the vent plate on the

electric bumper boat.

(J&J #001688)

“Water Bug” decal is located on the

boat top above the water drain plug

on the gas bumper boat.

(J&J #00168)

“Warning-Keep Hands And Feet In Boat At All

Times”

decal is located on the right inboard side of the

boat top.

(J&J #00169)

<SAFETY ITEM>

This decal must be readable at all times to operate

the boat.

Replace as needed.

Keep your boats looking new with
Replacement decals available at j&j

«
...
157
158
159
160
161
...
»

Summary of Contents for Bumper Boat 2014









































































































































































Reviews:

No comments

Related manuals for Bumper Boat 2014

Brand: Williams Pages: 134

Brand: Edgewater Networks Pages: 39

NorthCoast 255 Hard Top

Brand: C&C Pages: 52

Brand: Grady-White Boats Pages: 66

Brand: Grady-White Boats Pages: 91

Brand: Malibu Boats Pages: 76

Brand: Pelican Pages: 4

Brand: Mercury Pages: 36

Brand: Mercury Pages: 40

Brand: Gumotex Pages: 36

Brand: BENETEAU Pages: 238

Brand: Zboat Pages: 35

Brand: WASZP Pages: 17

Crossover 90490

Brand: Nautiques Pages: 198

Brand: Quicksilver Pages: 45

Brand: Quicksilver Pages: 60

WaveRunner XL800 2001

Brand: Yamaha Pages: 136

WaveRunner VX110 Sport

Brand: Yamaha Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands