J&J Amusements Bumper Boat 2014 Service Manual Download

Page: 43 / 168

1-9

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

The pivot is attached with 8 bolts and nylock nuts, and 16 flat

washers.

REMOVAL/INSTALLATION

Remove the bolts, nylock nuts and washers.

Install a new pivot by using the existing holes.

Replace the hardware with new hardware as needed.

ID PLATE:

Remove the ID plate from the old pivot.

Install the ID plate to the new pivot with 4 stainless steel

rivets.

VISIT WWW.JJAMUSEMENTS.COM/TECHNICAL/INDEX.HTM FOR
TECHNICAL INFORMATION RELATED TO OUR PRODUCTS.

PIVOT RECEIVER REMOVE/INSTALLATION

Summary of Contents for Bumper Boat 2014








































































































































































Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands

J&J Amusements Bumper Boat 2014, Service Manual

Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands