manualshive.com logo in svg

J&J Amusements Bumper Boat 2014, Service Manual

The J&J Amusements Bumper Boat 2014 offers thrilling water-based entertainment for all ages. Unlock the full potential of this exhilarating ride by accessing our comprehensive Service Manual. Download it for free at manualshive.com, guaranteeing a seamless and enjoyable experience for you and your guests.

Share
Download
background image

0-7

 SPECIFICATIONS: ELECTRIC-POWERED

BLASTER BOAT.

DIMENSIONS:

Overall diameter .......................................................................................................................................72”(182 cm)
Overall height ...........................................................................................................................................40”(101 cm)
Wet weight .............................................................................................................................................488lbs(222kg)
Total battery weight ................................................................................................................................248lbs(113kg)
Super Tube II weight...................................................................................................................................23lbs(11kg)
Hull & deck weight ..................................................................................................................................139lbs(63kg)
Minimum water depth ....................................................................................................................................3ft(.91m)

MOTOR: 

Model.....................................................................................................................................................24v 1750 rpm
Type ......................................................................................Continuous duty 3/4 hp(1118w) 24v, permanent magnet
Motor weight ..............................................................................................................................................78lbs(36kg)
Cooling system ........................................................................................................................................................ Air
Maximum horsepower.......................................................................................................................3/4 hp(1750 rpm)
Maximum speed .............................................................................................................................. 3.5 mph(4.8 km/h)
Throttle........................................................................................................................Green rod / push button (on/off)
Squirt............................................................................................................................. Blue rod / push button (on/off)
Squirter Type .......................................................................................................................................24v submersible

BATTERY: 

Type ................................................................................................................................... 6 volt deep cycle (225 AH)
Weight ....................................................................................................................................................62 lbs (28 kg)
Length .................................................................................................................................................10 3/8(264 mm)

LOWER UNIT:

Gear ratio ................................................................................................................................................................1:1
Propeller......................................................................................................................3-7.2 x 4.7 in(3-184 x 120 mm)
Rotating direction ............................................................................................................Clockwise (viewed from rear)

Summary of Contents for Bumper Boat 2014









































































































































































Reviews:

No comments

Related manuals for Bumper Boat 2014

Jeanneau 64 Owner'S Manual preview
64
Brand: Jeanneau Pages: 80
Zodiac MEDLINE 7.5 Manual preview
MEDLINE 7.5
Brand: Zodiac Pages: 55
YAMARIN 56 Hard Top Owner'S Manual preview
56 Hard Top
Brand: YAMARIN Pages: 35
Cobalt Digital Inc 282 BOWRIDER Owner'S Manual preview
282 BOWRIDER
Brand: Cobalt Digital Inc Pages: 130
Maverick Boat Company Pathfinder 2300 HPS Owner'S Manual preview
Pathfinder 2300 HPS
Brand: Maverick Boat Company Pages: 20
komodo KDKX1INFKYA User Manual preview
KDKX1INFKYA
Brand: komodo Pages: 12
Sea-doo GTI 5865 Shop Manual preview
GTI 5865
Brand: Sea-doo Pages: 316
Sea-doo GTS 5815 Shop Manual preview
GTS 5815
Brand: Sea-doo Pages: 618
La Rochelle Dufour 36 Owner'S Manual preview
Dufour 36
Brand: La Rochelle Pages: 72
Ranger 191 CAYMAN Owner'S Manual preview
191 CAYMAN
Brand: Ranger Pages: 78
Mercury 10 Marathon Operation, Maintenance & Installation Manual preview
10 Marathon
Brand: Mercury Pages: 87
Nauticstar XTS 195 Owner'S Manual preview
XTS 195
Brand: Nauticstar Pages: 80
Sea-doo 2001 GS 5548 Operator'S Manual preview
2001 GS 5548
Brand: Sea-doo Pages: 100
Sea-doo 1999 GS Operator'S Manual preview
1999 GS
Brand: Sea-doo Pages: 109
Hunter Legend 37 Owner'S Manual preview
Legend 37
Brand: Hunter Pages: 23
S2 Yachts 8.0 B Owner'S Manual preview
8.0 B
Brand: S2 Yachts Pages: 43
Pakboats XT-15 solo Assembly Instructions And User'S Manual preview
XT-15 solo
Brand: Pakboats Pages: 8
Xo 240 RS Cabin User Manual preview
240 RS Cabin
Brand: Xo Pages: 53

Brands by name

Popular brands

Load more brands