J&J Amusements Bumper Boat 2014 Service Manual Download

Page: 60 / 168

1-26

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

Place the boat top on the hull.

Open the vent plate to access the rubber hinge.

Pre-drill through the rubber hinge.

Insert six rivets through the hull and rubber hinge.

Insert a backing washer on inside of each rivet.

Holding the backing plate, insert the rivets.

Connect all wiring connections

(see wiring diagram on page 4-18).

VISIT WWW.JJAMUSEMENTS.COM/TECHNICAL/INDEX.HTM FOR
TECHNICAL INFORMATION RELATED TO OUR PRODUCTS.

Summary of Contents for Bumper Boat 2014








































































































































































Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands

J&J Amusements Bumper Boat 2014, Service Manual

Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands