J&J Amusements Bumper Boat 2014 Service Manual Download

Page: 93 / 168

3-5

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

Each control rod has a spring located between the rod and

the bottom of the tube.

If the rod doesn’t return to the fully raised position, the

spring will need to be replaced.

Unbolt the magnetic trigger to remove the control rod.

Use a magnet to remove the spring.

The countersink hole in the control rod faces the slot on

the handlebar.

Line up the countersink hole on the control rod with the

slot in the handlebar.

Install the magnetic trigger and make sure to orient the

trigger with the magnet facing down, so the trigger can

function properly.

NOTICE:

Apply anti-seize to the threads on the shoulder bolt.

CONTROL RODS

VISIT WWW.JJAMUSEMENTS.COM/TECHNICAL/INDEX.HTM FOR
TECHNICAL INFORMATION RELATED TO OUR PRODUCTS.

Spring

Summary of Contents for Bumper Boat 2014








































































































































































Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands

J&J Amusements Bumper Boat 2014, Service Manual

Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands