J&J Amusements Bumper Boat 2014 Service Manual Download

Page: 104 / 168

3-16

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

Before motor disassembly, make sure to mark the location of

the cap in relation to the motor casing.

NOTICE

If the motor cap is assembled 180 degrees off,

this will reverse polarity and cause the motor to turn counter-

clockwise.

Remove the fan cover.

Remove the fan bolt and slide the fan off of the shaft.

INFLATE AND DEFLATE BOAT TUBES QUICKLY
WITH THIS 4HP VACUUM/BLOWER! J&J# 2-60-0124

Summary of Contents for Bumper Boat 2014








































































































































































Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands

J&J Amusements Bumper Boat 2014, Service Manual

Search results

Summary of Contents for Bumper Boat 2014

Reviews:

Related manuals for Bumper Boat 2014

Brands by name

Popular brands