iSMA iSMA-B-LP-1 User Manual Download Page 65

Page: 65 / 122

iSMA-B-LP Room Panel/Modbus

version 1.3

www.gc5.pl

Page 64 / 121

Modbus
Address

Dec

Address

Hex

Address

Access

Description

that time. Default time: 500ms.

40222

221

0xDD

SUBMENU_ICON_FLASHING_TIME Read & Write

Memory

Time which is the base for calculating frequency of
Icon flashing. Icons are visible for 100% of the time

value stored in the register and hidden for 20% of

that time. Default time 1000ms.

40223

222

0xDE

ENTER_MENU_TIME

Read & Write

Memory

By default 2 sec.

40224

223

0xDF

EXIT_EDIT_TIME

Read & Write

Memory

By default 5 sec.

40225

224

0xE0

EXIT_MENU_TIME

Read & Write

Memory

By default 10 sec.

40226

225

0xE1

CO2_SETPOINT_FOR_ALARM

Read & Write

Memory

CO2 Alarm setpoint. By default 1500 ppm.

40227

226

0xE2

CO2_HYSTERESIS_FOR_ALARM

Read & Write

Memory

CO2 Alarm hysteresis. By default 100 ppm.

30230

229

0xE5

ALARM_STATUS

Read Only

CO2 Current alarm Status

30301

300

0x12C

TEMPERATURE_SENSOR

Read Only

Actual temperature sensor value with offset.

30302

301

0x12D

HUMIDITY_SENSOR

Read Only

Actual humidity sensor value with offset.

30303

302

0x12E

CO2_SENSOR

Read Only

Actual CO2 sensor value with offset.

40304

303

0x12F

TEMPERATURE_SENSOR_OFFSET Read & Write

Memory

Temperature sensor offset. Default is 0.

40305

304

0x130

HUMIDITY_SENSOR_OFFSET

Read & Write

Memory

Humidity sensor offset. Default is 0.

40306

305

0x131

CO2_SENSOR_OFFSET

Read & Write

Memory

CO2 sensor offset. Default is 0.

40307

306

0x132

TEMPERATURE_FILTER

Read & Write

Memory

By default 60 sec

40308

307

0x133

HUMIDITY_FILTER

Read & Write

Memory

By default 60 sec

40309

308

0x134

CO2_FILTER

Read & Write

Memory

By default 60 sec

40310

309

0x135

TEMPERATURE_NAME

(32

–

bits)

Read & Write

Memory

Displayed temperature sensor name. : TEMP

40312

311

0x137

HUMIDITY_NAME

(32

–

bits)

Read & Write

Memory

Displayed humidity sensor name. : HUMI

40314

313

0x139

CO2_NAME

(32

–

bits)

Read & Write

Memory

Displayed CO2 sensor name. : CO2

Summary of Contents for iSMA-B-LP-1



























































































































Search results

Summary of Contents for iSMA-B-LP-1

Reviews:

Related manuals for iSMA-B-LP-1

Brands by name

Popular brands

iSMA iSMA-B-LP-1, User Manual

Search results

Summary of Contents for iSMA-B-LP-1

Reviews:

Related manuals for iSMA-B-LP-1

Brands by name

Popular brands