Pag. 4
ENGLISH (Translation of original instructions)
4.1 - UNPACKING THE MACHINE
- Unpack the machine with the utmost care; avoid carrying out any
operation that could damage it.Once it has been unpacked, check
whether it is damaged.If you notice that it is not in correct working
order, DO NOT use it and inform your dealer.
- For packaging and transport purposes, some parts and accessories
are supplied disconnected from the machine. To assemble them,
carefully follow the instructi-ons given in the relevant sections.
- Contents of the package
- N° 1 Machine
- N° 1 or 2 Side brush/es
- N° 2 Ignition key
- N° 1 Instruction booklet
- N° 1 Spareparts’ list
- N° 1 Declaration of conformity
- N° 1 Warranty slip
- N° 4 Batteries
(on request)
- N° 1 Battery charger
(on request)
- N° 1 Unblocking key
In the case in which one of the above-mentioned parts is missing,please
inform your dealer straight away.
For security reason during the transport, the
ignition key as been fixed inside the bag containing
the technical documentation.
Take care to keep the packaging materials (bags,
cartons, pallets, hooks, etc...) out of the reach of
children.
3.1 -FOREWORD
The purpose of this manual is to inform the operator of the basic rules,
safety rules and criteria which must be observed when using, adjusting
and maintaining themachine. The machine has been developed and
manufactured to ensure an excellent performance andthe utmost
comfort and ease of operation in a variety of working conditions.
Before delivery, the machine has been checked at our factory and by
our dealer to make sure it is handed over to you in perfect working
order.To maintain the machinein this condition and ensure problem-
free operation, it is essential to follow the routine maintenance
instructions given in this handbook.
3.2 - UTILIZATION FIELD
The machine, composed of a brush and suction system,is to be used
EXCLUSIVELY to clean dry surfaces.Anyother use could be cause of
damage to people or things and is therefore PROHIBITED.
4.2 - Precautions to be taken before attempting to put
the machine at work:
To facilitate transport, the side brush/es haven't been assembled in
their actual work position.Therefore, before using the machine, assemble
them as shown in Par. 4.3.
4.3 - ASSEMBLING THE SIDE BRUSH
To assemble the side brush in its correct position, operate as follows:
1: Place the brush-rising lever 5 Fig.2 on the OFF position.
2: Unscrew the screw from the side brush motor’s shaft.
3: Take the protection away from the key.
4: Position the brush complete with flange on the shaft
5: Screw the blocking screw back.
4.4:
PREPARING THE BATTERY FOR
OPERATION AN CHARGING.
To charge the battery,proceed as described below.
4.4.1 FIRST CHARGE
- Remove the caps of the battery cells.
- Fill the battery with electrolytic liquid.
- It is advisable to carry out this operation before the battery is mounted
on the machine from being damaged by the electrolytic liquid of the
battery.This operation should be done in a sufficiently ventilated
environment.Do not smoke.Now put the battery in its housing and
connect it appropriately,making sure torespect the polarity.
Connect the battery charger to the socked Fig 2 located on the rear part
of the machine and charge for at least 2 hours.
After charging, put the caps back on the battery cells.
4.4.2:RECHARGING
With the machine turned off:
- Remove the caps of the battery cells.
- Top up the battery with distilled water.
Connect the battery charger (Fig.2)
Carry this operation out following the NOTE instructions of
paragraph 4.4.1
4.4.3 CONNECTING THE BATTERIES
Connect the 4 batteries as shown in the pictures:
Fig.1
Summary of Contents for 1010 E
Page 1: ...1010 E JET 1000 E 1020 E...
