nugg
nugg
JVMU
JVMU
Using the JANUS 2050 Software
3-15
3
{
source}:install {country} -{port}
where:
source specifies the disk drive where the JANUS 2050 companion disk 1 is
inserted.
country specifies in what language you want the JANUS 2050 to operate.
Enter the name of the country. It must be one supported by DOS National
Language Support (NLS). This parameter is optional; the default is USA.
port specifies the host computer’s serial COM port that the JANUS 2050 is
connected to. This parameter is optional; the default is COM1.
For example, if Companion Disk 1 is in drive A, and the JANUS 2050 is
connected to COM1 on the host computer, enter the following command to
make the JANUS 2050 operate in English:
A:install
If Companion Disk 1 is in drive B, and the JANUS 2050 is connected to
COM2 on the host computer, enter the following command to make the
JANUS 2050 operate in French:
B:install france -com2
3. Wait for the installation procedure to finish, and follow any instructions on
the host computer’s display.
The install procedure creates a subdirectory C_FILES\COMMON on your host
computer that contains the factory default startup files AUTOEXEC.BAT and
CONFIG.SYS. You can edit these files before loading them onto the JANUS
2050, but be careful not to remove or alter clearly commented statements that
are used to support the Auto-Loader utility. Any files added to the
subdirectory \COMMON are ignored when the startup files are loaded on the
JANUS 2050.
The install procedure also creates the following batch files on the host
computer.
LOADC.BAT
This is a master file that is called by the following batch files.
LOAD_USA.BAT
or
LOADLANG.BAT
Creates an image file that contains only the
new startup files. It then loads the drive image onto the JANUS 2050 drive C
and overwrites all existing files. Any non-startup files are deleted from drive C.
Which batch file you use depends on whether you specified USA or another
country when loading the Auto-Loader utility.
LOADADD.BAT
Creates an image file that contains additional files you specify,
and loads the drive image onto the JANUS 2050 drive C without replacing the
existing JANUS 2050 AUTOEXEC.BAT and CONFIG.SYS. All existing files on
drive C remain intact unless they are replaced by new files with the same
name.
Summary of Contents for Janus 2050
