JANUS 2050 Vehicle-Mount Computer User’s Manual (4MB)
39
nugget
A
8-10
Using PC Cards
This table lists problems that may occur when you use a PC card in the JANUS
2050.
Problem
Solution
The JANUS 2050 beeps twice when you
insert a card in the PC card drive.
The JANUS 2050 cannot read the PC card in drive G. You need
to format the PC card.
The JANUS 2050 locks up when you are
accessing a PC card in drive G while
using Interlnk/Intersvr.
You cannot access a flash card in the JANUS 2050 PC card drive
if you are running Interlnk on the host computer. Run Interlnk
on the JANUS 2050 and Intersvr on the host computer if you
want to access a flash card in the JANUS 2050 PC card drive.
The JANUS 2050 locks up frequently
when you are accessing the PC card
in the PC card drive.
The PC card may not be formatted correctly. If you formatted
the PC card on your PC or host computer, try formatting the
card in the JANUS 2050 PC card drive.
You are trying to access the JANUS
2050 PC card drive and you see the
message “Invalid media type reading
drive G.”
Press
A
to abort. The JANUS 2050 cannot read the PC card in
the drive. Use the CARDINFO utility to verify the type of card
you are using (ATA, flash, I/O, or SRAM).
Check the JANUS 2050 CONFIG.SYS file. Make sure you have
the correct drivers installed for the type of card you are using.
Format the PC card.
You are trying to access the JANUS
2050 PC card drive and you see the
message, “Not ready reading drive G.
Abort, Retry, Fail?”
Press
A
to abort. The JANUS 2050 cannot read the PC card in
the drive. Use the CARDINFO utility to verify the type of card
you are using (ATA, flash, I/O, or SRAM).
Check the JANUS 2050 CONFIG.SYS file. Make sure you have
the correct drivers installed for the type of card you are using.
Format the PC card.
You may also see this message if you are using the Substitute
command and you do not have a PC card in the PC card drive.
Insert a PC card in each drive and try using the Substitute
command again.
You are trying to access the JANUS
2050 PC drive and you see the
message, “Bad command or file.”
Check the command you entered and make sure it is a valid
command. Try entering the command again.
Summary of Contents for Janus 2050
