6 / 27
P/N 466-2488 • REV A • ISS 02JUL13
5. Press the * key to enter the data and move to the next
segment. Press # to leave the location before the last
segment.
6. When you have programmed the last segment of the
location, press the * key to exit the location.
7. Enter another location number followed by the # key if you
wish to program another location.
8. Leave programming mode by pressing the Exit key on the
keypad.
Enrolling the Transmitters
8 wireless transmitters can be enrolled on the receiver for use
with the Quik Bridge®. You can either enrol the transmitters
individually or use the auto enrol feature to enrol several
transmitters at the same time. In each case you must activate
the tamper on the transmitter as shown in Table 4.
Table 4: Transmitter activations
Transmitter Action
Door/Window
Remove the cover
Door/Window with external
contact
Remove the cover
PIR
Remove the cover
Smoke detector
Remove the backplate
4 button keyfobs
Press the Arm and Disarm buttons
simultaneously (433 MHz), or see
the keyfob’s documentation
(868 MHz).
It is a good idea to make a note of the transmitter assigned to
each zone on the receiver.
Enrolling transmitters
1. Make sure that the dipswitch on the Receiver is set to 32.
2. To enter programming mode, press *8 followed by 9713.
3. Press 32# to program the RF Receiver module.
4. Press 910# to go to location 910. This loads the factory
defaults for the Receiver. The keypad beeps 3 times
indicating that loading is in progress. This takes about 6
seconds.
5. Press 194# to go to location 194. Check that Segment 1
is set to 0 so that the starting zone is 1. Press # to leave
the location.
6. Press 0 #1 * to enroll transmitter 1. Open the tamper on
the transmitter and the keypad should chime to indicate
that the transmitter has been accepted.
7. Repeat step 6 for the other devices by entering
0#
transmitter number
* and opening the tamper on the
transmitter for each device.
Auto enrolling transmitters
1. Make sure that the dipswitch on the NX Receiver is set to
32.
2. To enter programming mode, press *8 followed by 9713.
3. Press 32# to program the RF Receiver module.
4. Press 910# to go to location 910. This loads the factory
defaults for the Receiver. The keypad beeps 3 times
indicating that loading is in progress. This takes about 6
seconds.
5. Press 194# to go to location 194. Check that Segment 1
is set to 0 so that the starting zone is 1. Press # to leave
the location.
6. Press 193# to go to location 193. Check that segment 2
is on to allow sequential programming. Press # to leave
the location.
7. Press 0 #1* to enrol transmitter 1. Open the tamper on the
transmitter and the keypad should chime to indicate that
the transmitter has been accepted.
8. Open the tamper on each other transmitter to enrol the
devices sequentially.
Unenrolling transmitters
1. To enter programming mode, press *8 followed by 9713.
2. Press 32# to program the RF Receiver module.
3. Enter the transmitter number followed by #. For example,
for transmitter 4, enter 4#.
4. In Location 1 Segment 1 switch bit 1 off to disable the
transmitter.
5. Press * to save the setting and # to leave the menu.
RF Supervision windows for Belgium and Holland
(868 MHz)
1. Make sure that the dipswitch on the Receiver is set to 32.
2. To enter programming mode, press *8 followed by 9713.
3. Press 32# to program the RF Receiver module.
4. Press 195# to go to location 195.
For Holland and Belgium, check the correct values in Table 5.
Table 5: Supervision windows for Belgium and Holland
Segment 1
Segment 2
Segment 3
Holland 120
(long
supervision
window)
120 (long
supervision
window)
20 (short
supervision
window)
Belgium 120
(fire
transmitters
supervision
window)
120 (fire
transmitters
supervision
window)
20 (short
supervision
window)
RSSI values (868 MHz)
1. To enter programming mode, press *8 followed by 9713.
2. Press 32# to program the RF Receiver module.
3. Enter 10X# where X is the zone number (1 through 8).
4. Note the RSSI reading and repeat steps 3 to 4 for other
detectors.
Using the 4 button keyfobs
The functions of the Star and the Light buttons can be used to
trigger outputs. This can be achieved by programming receiver
options 4 and 5 of the zone segment where the keyfob was
enrolled.
Table 6: Star and Light button programming
Light Button
Option 4 Off
Option 4 On
Not Used
Output 1 Control
