manualshive.com logo in svg

Intel Stratix 10, User Manual

The Intel Stratix 10 is an advanced technology product, boasting unmatched performance and versatility. Enhance your understanding and unleash its potential by accessing the comprehensive user manual, available for free download from our website. Harness the power of Intel Stratix 10 with our user-friendly manual—your key to unlocking its full capabilities.

Share
Download
background image

power-up, which may or may not be the same as what is configured in the transceiver
IP. A difference in the configured 

refclk

 in the IP compared to the available 

refclk

on the board can cause unexpected transitions on the E-Tile TX output.

Make sure you are okay with this behavior until the 

refclk

 frequencies are set

correctly followed by the recommended reset and device configuration steps as per

PMA Analog Reset. If the unexpected transitions are not acceptable, you can disable

the transceiver TX output by writing the attribute code 0x0001 with data 0x0003 after

power-up. The E-Tile TX may still give some unexpected transitions between the

power-up phase until the attribute code 0x0001 is written.

After correctly configuring back the on-board reference clock, follow the recommended

reset and device configuration steps as per PMA Analog Reset to reset the internal

controller. Refer to the Register Map for more details on attribute codes and data.

4. Clock Network

UG-20056 | 2019.02.04

Send Feedback

Intel

®

 Stratix

®

 10 E-Tile Transceiver PHY User Guide

87

Summary of Contents for Stratix 10





































































































































































































































Reviews:

No comments

Related manuals for Stratix 10

Cypress Semiconductor CY7C1034DV33 Specification Sheet preview
CY7C1034DV33
Brand: Cypress Semiconductor Pages: 9
Freescale Semiconductor FRDM-STBC-SA9500 Quick Reference Card preview
FRDM-STBC-SA9500
Brand: Freescale Semiconductor Pages: 2
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
Aruba IntroSpect Analyzer 2 Series Quick Start Manual preview
IntroSpect Analyzer 2 Series
Brand: Aruba Pages: 5
Parker ACR1200 Hardware Manual preview
ACR1200
Brand: Parker Pages: 50
JETWAY HBJC924R3288DG2NS Series Quick Installation Manual preview
HBJC924R3288DG2NS Series
Brand: JETWAY Pages: 6
Echo LAYLA 3G Owner'S Manual preview
LAYLA 3G
Brand: Echo Pages: 21
Baikal Miner GIANT PlUS User Manual preview
GIANT PlUS
Brand: Baikal Miner Pages: 14
Genexis FiberTwist XGS2410 Installation Manual preview
FiberTwist XGS2410
Brand: Genexis Pages: 7
Ultra Products Internal All-in-One Digital Media Drive ULT31793 Specifications preview
Internal All-in-One Digital Media Drive ULT31793
Brand: Ultra Products Pages: 1
CSI 7798 I/SITE LAN Installation Manual preview
7798 I/SITE LAN
Brand: CSI Pages: 56
XMOS XK-XMP-64 Hardware Manual preview
XK-XMP-64
Brand: XMOS Pages: 10
Transition Networks PCM16-FX-LC-01 User Manual preview
PCM16-FX-LC-01
Brand: Transition Networks Pages: 5
Opengear OG-HDTV-SDI-UHD User Manual preview
OG-HDTV-SDI-UHD
Brand: Opengear Pages: 7
OPTO 22 BD-DEVNET User Manual preview
BD-DEVNET
Brand: OPTO 22 Pages: 28
Planet FGSW-4840S User Manual preview
FGSW-4840S
Brand: Planet Pages: 38
ICP DAS USA PEX-P8R8i Quick Start Manual preview
PEX-P8R8i
Brand: ICP DAS USA Pages: 9
Curtiss-Wright KAD/UBM/105 Quick Start Manual preview
KAD/UBM/105
Brand: Curtiss-Wright Pages: 12

Brands by name

Popular brands

Load more brands