Intel Stratix 10 User Manual Download

Page: 120 / 228

7.1. Dynamically Reconfiguring Channel Blocks

Table 51.

Intel Stratix 10 Dynamic Reconfiguration Feature Support

Reconfiguration

Features

Channel Reconfiguration

PMA Analog Features such as:
• VOD
• Pre-emphasis
• Enable RX adaptation

Enable/disable RS-FEC. Read out RS-FEC statistics

Reconfigure between NRZ and PAM4 when in PMA direct mode

TX local clock dividers, reference clock

RX local clock dividers, reference clock

Clock output frequency

7.2. Interacting with the Dynamic Reconfiguration Interface

Each transceiver channel contains a reconfiguration interface shared with the PMA

Interface (PMAIF), PMA and Embedded Multi-die Interconnect Bridge (EMIB).

Additionally, there are six reconfiguration interfaces per E-Tile allowing access to the

six RS-FEC blocks.

The reconfiguration interface provides direct access to the programmable space of

each channel. Communication with the channel reconfiguration interface requires an

AVMM master. Because each channel has its own dedicated AVMM interface, you can

dynamically reconfigure channels either concurrently or sequentially, depending on

how the AVMM master is connected to the AVMM reconfiguration interface.

Figure 78.

Reconfiguration Interface in Intel Stratix 10 Transceiver IP Cores

Ch0: AVMM

Reconfiguration

Interface (1)

Ch1: AVMM

Reconfiguration

Interface (1)

Native PHY IP Core

Embedded Controller in FPGA

or External Processor on PCB

AVMM Master

Note:
1. The Native PHY IP core, user reconfiguration logic (AVMM master), interfaces
with the hard registers and EMIB using the AVMM reconfiguration interface.

A Native PHY IP core instance can specify multiple channels. You can use a dedicated

reconfiguration interface for each channel or share a single reconfiguration interface

across multiple channels to perform dynamic reconfiguration.

7. Dynamic Reconfiguration

UG-20056 | 2019.02.04

Intel

Stratix

10 E-Tile Transceiver PHY User Guide

Send Feedback

120

Summary of Contents for Stratix 10





































































































































































































































Search results

Summary of Contents for Stratix 10

Reviews:

Related manuals for Stratix 10

Brands by name

Popular brands

Intel Stratix 10, User Manual

Search results

Summary of Contents for Stratix 10

Reviews:

Related manuals for Stratix 10

Brands by name

Popular brands