Intel Stratix 10 User Manual Download

Page: 135 / 228

Parameter

Value

Description

Clear selected profile

N/A

Clears the stored Native PHY parameter settings for the

profile specified by the Store current reconfiguration

to profile parameter. An empty profile defaults to the

current parameter settings of the Native PHY. In other

words, an empty profile reflects the Native PHY current

parameter settings.

Clear all profiles

N/A

Clears the Native PHY IP parameter settings for all

profiles.

Refresh selected profile

N/A

Equivalent to clicking the Load configuration from

selected profile and Store configuration to selected

profile buttons in sequence. This operation loads the

parameter settings from stored profile specified by the

Store current configuration to profile parameter and

then stores the parameters back to the profile.

7.13. Embedded Debug Features

The Intel Stratix 10 Transceiver Native PHY IP cores provide the following optional

debug features to facilitate embedded test and debug capability:
•

Altera Debug Master Endpoint (ADME)

•

Optional Reconfiguration Logic

7.13.1. Altera Debug Master Endpoint (ADME)

The ADME is a JTAG-based AVMM master that provides access to the transceiver

registers through the system console. You can enable ADME using the Enable Altera

Debug Master Endpoint option available under the Dynamic Reconfiguration tab

in the Native PHY IP cores. When using ADME, the Intel Quartus Prime software

inserts the debug interconnect fabric to connect with USB, JTAG, or other net hosts.

Select the Share Reconfiguration Interface parameter when the Native PHY IP

instance has more than one channel. The Transceiver Toolkit, a useful tool in

debugging transceiver links, requires ADME.

When you enable ADME in your design, you must do one of the following:
•

Connect an AVMM master to the reconfiguration interface.

•

Connect the

reconfig_clk

reconfig_reset

signals and ground the

reconfig_write

reconfig_read

reconfig_address

, and

reconfig_write

data signals of the reconfiguration interface if not being driven

by other core logic. If you do not connect the reconfiguration interface signals

appropriately, the ADME has no clock or reset and functions unexpectedly. Refer to

the example connection below (this is an example of a single channel with no

internal logic driving the reconfig interface):

.reconfig_clk (mgmt_clk),
.reconfig_reset (mgmt_reset),
.reconfig_write (1'b0),
.reconfig_address (19'b0),
.reconfig_read (1'b0),
.reconfig_writedata (8'b0),

7. Dynamic Reconfiguration

UG-20056 | 2019.02.04

Send Feedback

Intel

Stratix

10 E-Tile Transceiver PHY User Guide

135

Summary of Contents for Stratix 10





































































































































































































































Search results

Summary of Contents for Stratix 10

Reviews:

Related manuals for Stratix 10

Brands by name

Popular brands

Intel Stratix 10, User Manual

Search results

Summary of Contents for Stratix 10

Reviews:

Related manuals for Stratix 10

Brands by name

Popular brands