manualshive.com logo in svg

Intel Stratix 10, User Manual

Share
Download
Intel Stratix 10 User Manual Download Page 67

3.1.2.3. Input Sampler

The Input Sampler block is responsible for converting the serial input signal into a

retimed bit stream using the high-speed serial clock generated by the CDR block.

3.1.2.4. Deserializer

The deserializer block clocks in serial input data from the receiver buffer using the

high-speed serial recovered clock, and deserializes the data using the low-speed

parallel recovered clock. The deserializer forwards the deserialized data to the receiver

PCS or FPGA core.

The channel deserializer supports the following deserialization factors: 16, 20, 32, 40,

and 64.

Figure 36.

Deserializer

The deserializer block sends out the LSB of the input data first.

Dn

D2

D1

D0

Serial

Data

LSB

Deserializer

Parallel

Clock

Clock

Serial

Dn

D2

D1

D0

Parallel

Data

3.1.2.5. Data Pattern Verifier

The data pattern verifier is used to verify the signal received at the receiver. The

deserialized data pattern is sent to the data pattern verifier, which compares the

received data pattern to the pattern it is configured to. There are several patterns

which can be verified in NRZ and PAM4 mode. For the same setting, depending on the

encoding mode, either PRBSx (NRZ) or PRBSxQ (PAM4) is configured.

Table 31.

PRBS Patterns by Mode

NRZ Mode

PAM4 Mode

PRBS7

PRBS7Q

PRBS9

PRBS9Q

PRBS11

PRBS11Q

PRBS13

PRBS13Q

PRBS15

PRBS15Q

continued...   

3. Intel Stratix 10 E-Tile Transceiver PHY Architecture

UG-20056 | 2019.02.04

Send Feedback

Intel

®

 Stratix

®

 10 E-Tile Transceiver PHY User Guide

67

Summary of Contents for Stratix 10





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands