Intel Stratix 10 User Manual Download

Page: 136 / 228

7.13.2. Optional Dynamic Reconfiguration Logic

The Intel Stratix 10 Transceiver Native PHY IP cores contain soft logic for debug

purposes known as the Optional Reconfiguration Logic. This soft logic provides a set of

registers that enable you to determine the state of the Native PHY IP cores.

You can enable the following optional reconfiguration logic options in the transceiver

Native PHY IP cores:
•

Capability registers

•

Control and status registers

7.13.2.1. Capability Registers

The capability registers provide high level information about the transceiver channel

configuration and capture a set of chosen capabilities of the PHY that cannot be

reconfigured. They are located on the PMA AVMM interface and are located on

addresses 0x40000 to 0x5FFFF.

Related Information
PMA Register Map

on page 165

7.13.2.2. Control and Status Registers

Control and status registers are optional registers that memory map the status

outputs from and control inputs to the Native PHY. The control and status registers are

located on the PMA AVMM interface from 0x40000 to 0x5FFFF.

Related Information
PMA Register Map

on page 165

7.14. Timing Closure Recommendations

Intel recommends that you enable the multiple reconfiguration profiles feature in the

Native PHY IP core if any of the modified or target configurations involve changes to

RS-FEC settings. Using multiple reconfiguration profiles is optional if the

reconfiguration involves changes to only PMA settings such as TX VOD swing or refclk

switching. When performing a dynamic reconfiguration, you must:
•

Include constraints to create the extra clocks for all modified or target

configurations at the RS-FEC -FPGA fabric interface. Clocks for the base

configuration are created by the Intel Quartus Prime software. These clocks enable

the Intel Quartus Prime Pro Edition to perform static timing analysis for all the

transceiver configurations and their corresponding FPGA fabric core logic blocks.

•

Include the necessary false paths between the RS-FEC – FPGA fabric interface and

the core logic.

For example, you can perform dynamic reconfiguration to switch the datapath from

PMA direct to RS-FEC using the multiple reconfiguration profiles feature. This feature

will be supported in a future Intel Quartus Prime release.

More details about how to create the false paths will be included in a future user guide

release.

7. Dynamic Reconfiguration

UG-20056 | 2019.02.04

Intel

Stratix

10 E-Tile Transceiver PHY User Guide

Send Feedback

136

Summary of Contents for Stratix 10





































































































































































































































Search results

Summary of Contents for Stratix 10

Reviews:

Related manuals for Stratix 10

Brands by name

Popular brands

Intel Stratix 10, User Manual

Search results

Summary of Contents for Stratix 10

Reviews:

Related manuals for Stratix 10

Brands by name

Popular brands