Intel Stratix 10 Page 133 User Manual Download

Page: 133 / 228

Table 54.

Reconfiguration Interface Ports with Independent Native PHY

Reconfiguration Interface

The reconfiguration interface ports when Share reconfiguration interface is disabled. <N> represents the

number of channels.

Port Name

Direction

Clock Domain

Description

reconfig_clk_ch<N-1>, ...,reconfig

_clk_ch0

Input

N/A

The clock frequency is 100-162

MHz.

reconfig_reset_ch<N-1>, ...,reconf

ig_reset_ch0

Input

reconfig_clk_ch#

Resets the AVMM interface.

Asynchronous assertion and

synchronous deassertion.

reconfig_write_ch<N-1>, ...,reconf

ig_write_ch0

Input

reconfig_clk_ch#

Write enable signal. Signal is active

high.

reconfig_read_ch<N-1>, ...,reconfi

g_read_ch0

Input

reconfig_clk_ch#

Read enable signal. Signal is active

high.

reconfig_address_ch<N-1>[18:0], ..

.,reconfig_address_ch0[18:0]

Input

reconfig_clk_ch#

An 20-bit address bus for each

channel.

reconfig_writedata_ch<N-1>[7:0], .

..,reconfig_writedata_ch0[7:0]

Input

reconfig_clk_ch#

A 8-bit data write bus for each

channel. Data to be written into the

address indicated by

reconfig_address

reconfig_readdata_ch<N-1>[7:0], ..

.,reconfig_readdata_ch0[7:0]

Output

reconfig_clk_ch#

A 8-bit data read bus for each

channel. Valid data is placed on this

bus after a read operation. Signal is

valid after

reconfig_waitrequest

goes

high and then low.

reconfig_waitrequest_ch<N-1>, ...,

reconfig_waitrequest_ch0

Output

reconfig_clk_ch#

A one-bit signal for each channel

that indicates that the AVMM

interface is busy. Keep the AVMM

command asserted until the

interface is ready to proceed with

the read/write transfer.

Table 55.

AVMM Interface Parameters

The following parameters are available in the Dynamic Reconfiguration tab of the Transceiver Native PHY

parameter editors.

Parameter

Value

Description

Share reconfiguration interface

On/Off

Enables you to use a single reconfiguration interface to

control all channels. Off by default. If enabled, the
uppermost bits of

reconfig_address

identifies the

active channel. The lower 20 bits specify the

reconfiguration address. Binary encoding is used to

identify the active channel (available only for Transceiver

Native PHY). Enable this option, if desired, when the

Native PHY is configured with more than one channel.

Enable dynamic reconfiguration

On/Off

Enables the reconfiguration interface. Off by default. The

reconfiguration interface is exposed when this option is

enabled.

Enable Altera Debug Master Endpoint

On/Off

When enabled, the Altera Debug Master Endpoint (ADME)

is instantiated and has access to the AVMM interface of

the Native PHY. You can access certain test and debug

functions using System Console with the ADME. Refer to

the "Embedded Debug Features" section for more details

about ADME.

continued...

7. Dynamic Reconfiguration

UG-20056 | 2019.02.04

Send Feedback

Intel

Stratix

10 E-Tile Transceiver PHY User Guide

133

Summary of Contents for Stratix 10





































































































































































































































Search results

Summary of Contents for Stratix 10

Reviews:

Related manuals for Stratix 10

Brands by name

Popular brands

Intel Stratix 10, User Manual

Search results

Summary of Contents for Stratix 10

Reviews:

Related manuals for Stratix 10

Brands by name

Popular brands