Intel Stratix 10 User Manual Download | Manualshive

Page: 19 / 228

background image

Channel bonding is a common technique used to minimize high speed serial lane-lane

transmit skew for multi-lane protocols. Channel bonding is supported under the

following conditions:
•

Using

refclk[0]

•

NRZ PMA direct mode

•

Data rate limited to:
— 16-bit (parallel data width): 12.0 Gbps
— 20-bit (parallel data width): 16.0 Gbps
— 32-bit (parallel data width): 28.0 Gbps

Note:

Bonding is only supported within a tile. Bonding is not supported within a package

across different tiles, even if the reference clock is shared.

Figure 12.

TX and RX with the Same Reference Clock

This configuration shows

refclk[1]

being used for TX and RX on both channels, enabling use of the same

reference clock.

Transmitter

Receiver

Channel 0

Unused

Transmitter

Receiver

Channel 1

ref

clk[0]

ref

clk[1]

refclk_in_B

ref

clk[8:2]

refclk_in_B

Related Information

•

Intel Stratix 10 Device Datasheet

•

Intel Stratix 10 Device Family Pin Connection Guidelines

1.4.4. Ethernet Hard IP (EHIP)

The Ethernet Hard IP is a hardened core of assorted multi-lane and single-lane

Ethernet components.

Intel Stratix 10 E-Tiles include four instances of the Ethernet Hard IP, which in turn

supports up to four multi-lane Ethernet MAC stacks, or 24 channels of single-lane

Ethernet channel (MAC/PCS) support.

1. Intel

®

Stratix

®

10 E-Tile Transceiver PHY Overview

UG-20056 | 2019.02.04

Send Feedback

Intel

®

Stratix

®

10 E-Tile Transceiver PHY User Guide

19

«
...
17
18
19
20
21
...
»

Summary of Contents for Stratix 10





































































































































































































































Reviews:

No comments

Related manuals for Stratix 10

Brand: Harman Kardon Pages: 66

Brand: Q-See Pages: 2

Brand: LevelOne Pages: 31

Brand: Grizzly Pages: 9

Brand: Buffalo Pages: 2

Brand: Omron Pages: 13

Brand: A4Tech Pages: 8

DL-DVI-Vision-IP Series

Brand: G&D Pages: 228

CY62136EV30 MoBL

Brand: Cypress Semiconductor Pages: 12

Brand: Promise Technology Pages: 26

Brand: B&B Electronics Pages: 17

Brand: Omron Pages: 29

Power System S914

Brand: IBM Pages: 48

Mustang-M2AE-MX1

Brand: IEI Technology Pages: 58

Brand: sound4 Pages: 66

Brand: Cypress Semiconductor Pages: 31

ExtremeCloud Appliance E1120

Brand: Extreme Networks Pages: 219

AMSTX-CF Series

Brand: ADLINK Technology Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands