manualshive.com logo in svg

Intel Stratix 10, User Manual

The Intel Stratix 10 is an advanced technology product, boasting unmatched performance and versatility. Enhance your understanding and unleash its potential by accessing the comprehensive user manual, available for free download from our website. Harness the power of Intel Stratix 10 with our user-friendly manual—your key to unlocking its full capabilities.

Share
Download
background image

The reset values in this table represents register values after a reset has completed.

Bit Name

Description

SW Access

HW Access

Protection

Reset

1:0

frac

Main operation mode:
0 none: Non-fractured, supporting e.g. 100GE, 128GFC:
One client using all 4 physical lanes.
Register tables indexed by physical lane# only uses entry 0, unless otherwise specified.
1 reserved1
2 reserved2
3 frac4: Fractured, supporting e.g. 25GE, 32GFC:
Four clients, each using 1 physical lane.

RW
RO
-

0x0

9.5.6. rsfec_lane_cfg

Register Name

Description

Address

Addressing Mode

rsfec_lane_cfg_0

RS-FEC per lane configuration

0x40

32-bits

rsfec_lane_cfg_1

0x44

rsfec_lane_cfg_2

0x48

rsfec_lane_cfg_3

0x4C

The reset values in this table represents register values after a reset has completed.

Bit

Name

Description

SW Access

HW Access

Protection

Reset

3

rs544

Selects the RS encoder/decoder mode:
0: Use RS(528,514).
1: Use RS(544,514).

RW
RO
-

0x0

2

indic_byp

Bypass error indication (to reduce latency):
0: Sync headers in the 66b words extracted from uncorrectable FEC codewords are

deliberately invalidated.
1: 66b words extracted from uncorrectable codewords are not explicitly marked bad.

When number of symbol errors in a block of 8192 consecutive codewords has

exceeded 417 with RS528 and 6380 with RS544, then sync header errors will be

generated towards the PCS layer for a period of 60ms to 75ms.

RW
RO
-

0x0

1

scr

Set to enable PN-5280 scrambling/descrambling.
Must be set to 1 when RS-FEC_CORE_CFG.frac = frac4 and RS-FEC_LANE_CFG.fc = 1

(i.e. 32GFC), otherwise it must be set to 0.

RW
RO
-

0x0

0

fc

Set to enable Fibre Channel mode.

RW
RO
-

0x0

9.5.7. tx_aib_dsk_status

Description

Address

Addressing Mode

Status fields for TX Deskew

0x104

32-bits

9. Register Map

UG-20056 | 2019.02.04

Send Feedback

Intel

®

 Stratix

®

 10 E-Tile Transceiver PHY User Guide

197

Summary of Contents for Stratix 10





































































































































































































































Reviews:

No comments

Related manuals for Stratix 10

Alcad ZA-431 Quick Start Manual preview
ZA-431
Brand: Alcad Pages: 6
Tandberg Data Storagelibrary T24 Manual preview
Storagelibrary T24
Brand: Tandberg Data Pages: 28
Riverbed SteelCentral NetExpress Installation Manual preview
SteelCentral NetExpress
Brand: Riverbed Pages: 38
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Brand: IEI Technology Pages: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Brand: Dahua Technology Pages: 14
Nvidia DGX A100 User Manual preview
DGX A100
Brand: Nvidia Pages: 115
Velopex Extra-X Quick Start Manual preview
Extra-X
Brand: Velopex Pages: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Brand: Tandberg Data Pages: 6
Renesas RL78/G11 User Manual preview
RL78/G11
Brand: Renesas Pages: 2
ZALMAN ZM-MFC1 Combo User Manual preview
ZM-MFC1 Combo
Brand: ZALMAN Pages: 7
LevelOne FSW-0808TX Quick Start Manual preview
FSW-0808TX
Brand: LevelOne Pages: 3
Z3 Technology DM8168-MOD-35 Manual preview
DM8168-MOD-35
Brand: Z3 Technology Pages: 22
8e6 Technologies HL-002-006 Quick Start Manual preview
HL-002-006
Brand: 8e6 Technologies Pages: 94
Miranda Imagestore Intuition+ User Manual preview
Imagestore Intuition+
Brand: Miranda Pages: 60
Alvarion BreezeNET DS.11 Configuration Utility Release Note preview
BreezeNET DS.11 Configuration Utility
Brand: Alvarion Pages: 2
Beck com.tom INDUSTRY 100.WLAN.W Startup Manual preview
com.tom INDUSTRY 100.WLAN.W
Brand: Beck Pages: 2
ASROCK IMB-X1314 User Manual preview
IMB-X1314
Brand: ASROCK Pages: 45
Huawei CR-P1RS Specifications preview
CR-P1RS
Brand: Huawei Pages: 2

Brands by name

Popular brands

Load more brands