Intel D815EEA2 Product Manual Download | Manualshive

Page: 76 / 96

background image

Intel Desktop Boards D815EEA2, D815EPEA2, D815EFV, and D815EPFV Product Guide

76

Hard Disk Drives Submenu

To access this menu, select Boot from the menu bar, then Hard Disk Drives.

Maintenance

Main

Advanced Security

Power

Boot

Exit

Boot

Device

Priority

Hard Disk Drives

Removeable

Devices

ATAPI

CDROM

Drives

The submenu represented in Table 28 is for setting hard disk drives.

Table 28.

Hard Disk Drives Submenu

Feature Options Description

1

st

Hard Disk Drive

(Note)

Dependent on installed
hard drives

Specifies the boot sequence from the available hard disk
drives. To specify boot sequence:

1. Select the boot device with <

↑

> or <

↓

>.

2. Press <Enter> to set the selection as the intended

boot device.

Note:

This boot device submenu appears only if at least one boot device of this type is installed. This list will display up
to twelve hard disk drives, the maximum number of hard disk drives supported by the BIOS.

Removable Devices Submenu

To access this menu, select Boot from the menu bar, then Removeable Devices.

Maintenance

Main

Advanced Security

Power

Boot

Exit

Boot

Device

Priority

Hard

Disk

Drives

Removeable Devices

ATAPI

CDROM

Drives

The submenu represented in Table 29 is for setting removable devices.

Table 29.

Removeable Devices Submenu

Feature Options

Description

1

st

Removeable Device

(Note)

Dependent on installed
removable devices

Specifies the boot sequence from the available
removable devices. To specify boot sequence:

1. Select the boot device with <

↑

> or <

↓

>.

2. Press <Enter> to set the selection as the

intended boot device.

Note:

This boot device submenu appears only if at least one boot device of this type is installed. This list will display up
to four removable devices, the maximum number of removable devices supported by the BIOS.

«
...
74
75
76
77
78
...
»

Summary of Contents for D815EEA2

































































































Reviews:

No comments

Related manuals for D815EEA2

Brand: 3xLogic Pages: 2

Brand: Direct IP Pages: 76

Brand: Xilica Audio Design Pages: 30

ER3-100 (5K02-55)

Brand: 8e6 Technologies Pages: 74

Brand: T.A Pages: 11

Brand: Advantech Pages: 36

Brand: ebm-papst Pages: 13

IPS Pro-Module-24C-GE-BP-TM

Brand: Trend Micro Pages: 3

J-Link-OB-STM32F072-128KB

Brand: Segger Pages: 18

CHEETAH ST34501FC

Brand: Seagate Pages: 68

Brand: Comtrend Corporation Pages: 4

Brand: Variscite Pages: 17

Brand: ICP Pages: 111

PC/104-PCMCIA-1

Brand: Kontron Pages: 20

2025ZCR - SCSI RAID Storage Controller

Brand: Adaptec Pages: 2

Brand: Dell Pages: 10

Brand: Vibe Pages: 12

Brand: StarTech.com Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands