Intel D815EEA2 Page 6 Product Manual Download

Page: 6 / 96

Intel Desktop Boards D815EEA2, D815EPEA2, D815EFV, and D815EPFV Product Guide

16. Connecting the Processor Fan Cable to the Processor Fan Connector ........................38

17. Attaching the Fan Heatsink Over the Processor ...........................................................39

18. Placing the Plastic Clip on the Fan Heatsink.................................................................39

19. Lowering the Plastic Clip Handle...................................................................................40

20. Attaching the Fan to the Fan Heatsink ..........................................................................41

21. Connecting the Processor Fan Cable to the Processor Fan Connector ........................41

22. Removing the Fan Heatsink..........................................................................................42

23. Removing the Battery from the D815EEA2 and D815EPEA2 Boards ...........................45

24. Removing the Battery from the D815EFV and D815EPFV Boards ...............................46

25. Connecting the IDE Cable (the D815EEA2 Board Is Shown)........................................47

26. BIOS Configuration Jumper Block Location (the D815EEA2 Board Is Shown) .............48

27. Connector Groups (the D815EEA2 Board Is Shown)....................................................79

28. Back Panel Connectors (the D815EEA2 Board Is Shown)............................................80

29. Audio Connectors (the D815EEA2 Board Is Shown).....................................................81

Power and Hardware Control Connectors (the D815EEA2 Board Is Shown) ................82

31. Add-in Board and Peripheral Interface Connectors for the D815EEA2 and

D815EPEA2 Boards .....................................................................................................83

32. Add-in Board and Peripheral Interface Connectors for the D815EFV and

D815EPFV Boards........................................................................................................84

33. Front Panel Connectors (the D815EEA2 Board Is Shown) ...........................................85

Tables

Board Differences .......................................................................................................... 9

Feature Summary .......................................................................................................... 9

Manufacturing Options..................................................................................................11

Supported Processors ..................................................................................................14

Processor and Memory Module Combinations..............................................................16

RJ-45 LAN Connector LEDs .........................................................................................22

Jumper Settings for the BIOS Setup Program Modes...................................................48

BIOS Setup Program Menu Bar....................................................................................57

BIOS Setup Program Function Keys.............................................................................58

10.

Maintenance Menu .......................................................................................................58

11.

Extended Configuration Submenu ................................................................................59

12.

Main Menu ....................................................................................................................60

13.

Advanced Menu............................................................................................................61

14.

PCI Configuration Submenu .........................................................................................62

15.

Boot Configuration Submenu ........................................................................................63

16.

Peripheral Configuration Submenu ...............................................................................64

17.

IDE Configuration Submenu .........................................................................................66

18.

Primary/Secondary IDE Master/Slave Submenus .........................................................67

19.

Diskette Configuration Submenu ..................................................................................68

20.

Event Log Configuration Submenu ...............................................................................69

21.

Video Configuration Submenu ......................................................................................70

22.

Security Menu...............................................................................................................71

23.

Power Menu..................................................................................................................72

24.

APM Submenu..............................................................................................................73

Summary of Contents for D815EEA2

































































































Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands

Intel D815EEA2, Product Manual

Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands